--- title: 'Between: 2024/03/01 en 2024/03/31 - 0110.be' canonical: https://0110.be/date/2024/3 markdown_url: https://0110.be/date/2024/3.md page: 0 posts_per_page: 30 total_posts: 2 filters: year: 2024 month: 3 previous: next: --- # Between: 2024/03/01 en 2024/03/31 - 0110.be ## [Measuring rain water tank level with an Arduino](https://0110.be/posts/Measuring_rain_water_tank_level_with_an_Arduino.md) - Published: 2024-03-28T00:00:00Z - Updated: 2024-03-29T10:47:07Z - Author: Joren - ID: 543 - Canonical: https://0110.be/posts/Measuring_rain_water_tank_level_with_an_Arduino - Tags: [UGent](https://0110.be/tags/UGent.md)

Fig: Submersible water level meter.

Due to the climate crisis, long droughts are becoming more common in Western Europe during the summers. Conversely, during the winters, it seems that there is more and more extreme rainfall. With [record breaking](https://www.meteo.be/nl/klimaat/klimaat-van-belgie/klimatologisch-overzicht/2024/februari) droughts and rainfall, it is essential that enough rainwater buffering capacity is available. As a private citizen this means installing a large rain water tank - perhaps larger than outdated models suggest - and using the captured water effectively, if at all possible.

Fig: Submersible water level meter.

To effectively use rain-water, it helps to have an easy way to view the water level in the tank. This makes clear when to conserve water or when a pump might end up running dry and overheat. So I wanted to install **a water level measurement device in my rain water tank**. My first attempt used sonar. This sends out a sound-wave which reflects on the water surface. The sonar measures the time it takes for the echo to return. This setup is finicky in an echoy tank but I managed to get it working. However, after couple of months the sonar stopped working in the damp environment. Next I tried a optical, infra-red-based setup: the idea was to time the infra-red reflection on the water. After installation it appeared that water is transparent for infra-red. I basically measured the position of the floor of my tank. I took comfort in the fact that this measurement remained stable but had to look for a third option. I finally became aware of sturdy, submersible pressure sensors which are designed for water level measurements. One of those is the QDY30A sensor, which is available in many versions but there is one which takes five volts as input and returns a 0 - 3.3V output: ideal to use with about any modern micro-controller. The sensor can be connected via a long cable. This helps to keep the Arduino in a dry place indoors. After recording a few measurements and the corresponding sensor depth, the sensor seems to show a very linear response: with two references, converting a sensor value to a depth in millimeters is doable. The readings ended up on a website and are [visualized via a SVG sparkline](https://alexplescan.com/posts/2023/07/08/easy-svg-sparklines/).
Fig: Rain water level visualization for a few days, measured every 15 minutes. Going from 221cm to 197cm. With the Arduino code attached you should be able to get going. Next to reading and converting a sensor value, it also includes reading the median of several values to add some smoothing. The sensor is read on request: only when a serial message arrives a measurement is done. --- ## [Offloading authentication and user management to Keycloak - A minimal example with Nuxt and Litestar](https://0110.be/posts/Offloading_authentication_and_user_management_to_Keycloak_-_A_minimal_example_with_Nuxt_and_Litestar.md) - Published: 2024-03-13T00:00:00Z - Updated: 2024-03-19T09:13:26Z - Author: Joren - ID: 542 - Canonical: https://0110.be/posts/Offloading_authentication_and_user_management_to_Keycloak_-_A_minimal_example_with_Nuxt_and_Litestar - Tags: [GhentCDH](https://0110.be/tags/GhentCDH.md), [UGent](https://0110.be/tags/UGent.md)

At the [Ghent Center for Digital Humanities](https://www.ghentcdh.ugent.be/) we provide software services for researchers. Think about, for example, annotation platforms for ancient texts or collaborative databases with geographically referenced historical data. Each of those services need some kind of authentication and user management: some parts of the service might be public, some only accessible for researchers at Ghent University and other parts need to be accessible e.g. to external researchers or collaborators. Providing authentication, login-flows and user management for each and every service quickly becomes tedious and, frankly, boring. We went looking for a solution and stumbled on [Keycloak](https://www.keycloak.org/). Keycloak is an open source __Identity and Access Management__ system and is able to either authenticate users itself or pass through authenticate to other authentication providers like LDAP, GitHub, OAuth accounts, or others. It avoids the need to setup application-specific user management system. Flows like 'forget password', 'verify email', 'two factor authentication' are not part of your application itself but are provided by Keycloak. Leaving the developer to focus on application specific tasks.

Video: An API call to a protected back-end first fails. After authentication and receiving a JWT token, the back-end call succeeds. The authenticated session is then shown in Keycloak. Integration with Keycloak is a bit of work and not straightforward. As part of trying out Keycloak I have created a [minimal working example of a front-end / back-end system which uses Keycloak for authentication](https://github.com/GhentCDH/nuxt-keycloak-jwt-auth/). To get full access to the back-end API the user first needs a valid JWT-token provided by Keycloak. The flow can be seen in the video above. The dockerized environment can perhaps serve as inspiration for similar setups. Please do try out the [dockerized minimal working example](https://github.com/GhentCDH/nuxt-keycloak-jwt-auth/) and see if Keycloak can fit your use-case. ---